- #Acom smart tool module drivers
- #Acom smart tool module driver
- #Acom smart tool module software
- #Acom smart tool module download
Your Data Link Adapter (DLA) should show a power ON light and possible blinking of a J1939 data light. For PLC, locate the trailer interface port at the front of the trailer.
#Acom smart tool module driver
Plug the J1939 diagnostic harness adapter of your Data Link unit into the vehicle diagnostics port this port is usually found under the dash, in the driverside left corner knee-space or along the left side of the driver seat mounting rail. Wait until the chuff test is completed or a minimum of 40 seconds after turning the key. The dash display should light up and the vehicle will begin its electronic readiness check, as well as the chuff test, if it is equipped with air brakes. Insert the key in the ignition and turn it to the 3 rd position On / Run (not to be confused with Engine Start). Look for the Bendix label and part number before you start.
#Acom smart tool module software
Before Starting The ACom Software IMPORTANT Confirm you are working with genuine Bendix parts. Keys to the vehicle and a fully charged vehicle battery, or an auxiliary battery tender, to support extended ignition - ON mode. A powered, fully functioning J1939 or PLC diagnostics port on the host vehicle or trailer.
#Acom smart tool module drivers
An RP1210 data link or Power Line Communication (PLC) adapter with the latest drivers and firmware installed.
#Acom smart tool module download
ACom software is available for download at. The latest version of Bendix ACom diagnostic software installed. 2ģ Bendix ACom Diagnostic Software Minimum Requirements A computer with the minimum system requirements to run Bendix ACom diagnostic software - see Appendix 3. You should consult the vehicle manufacturer's operating and service manuals, and any related literature, in conjunction with the Guidelines above. The power MUST be temporarily disconnected from the radar sensor whenever any tests USING A DYNAMOMETER are conducted on a vehicle equipped with a Bendix Wingman system. For vehicles with Automatic Traction Control (ATC), the ATC function must be disabled (ATC indicator lamp should be ON) prior to performing any vehicle maintenance where one or more wheels on a drive axle are lifted off the ground and moving. Prior to returning the vehicle to service, make certain all components and systems are restored to their proper operating condition. Do not attempt repairs requiring machining or welding unless specifically stated and approved by the vehicle and component manufacturer. Components with stripped threads or damaged parts should be replaced rather than repaired. must be of equivalent size, type and strength as original equipment and be designed specifically for such applications and systems. Replacement hardware, tubing, hose, fittings, wiring, etc. Use only genuine Bendix brand replacement parts, components and kits. Never remove a component or plug unless you are certain all system pressure has been depleted. Slowly open connections with care, and verify that no pressure is present. Never connect or disconnect a hose or line containing pressure it may whip and/or cause hazardous airborne dust and dirt particles. Never exceed manufacturer s recommended pressures. Following the vehicle manufacturer s recommended procedures, deactivate the electrical system in a manner that safely removes all electrical power from the vehicle. If the vehicle is equipped with a Bendix AD-IS air dryer system, a Bendix DRM dryer reservoir module, or a Bendix AD-9si air dryer, be sure to drain the purge reservoir. If the work is being performed on the vehicle s air brake system, or any auxiliary pressurized air systems, make certain to drain the air pressure from all reservoirs before beginning ANY work on the vehicle. Use only the proper tools and observe all precautions pertaining to use of those tools. Do not attempt to install, remove, disassemble or assemble a component until you have read, and thoroughly understand, the recommended procedures.
Where circumstances require that the engine be in operation, EXTREME CAUTION should be used to prevent personal injury resulting from contact with moving, rotating, leaking, heated or electrically-charged components. When working in the engine compartment, the engine should be shut off and the ignition key should be removed. Stop the engine and remove the ignition key when working under or around the vehicle. Always wear personal protection equipment. 1 Bendix ACom Diagnostic Software Starter Guide Steps for proper installation and operation 1Ģ GENERAL SAFETY GUIDELINES WARNING! PLEASE READ AND FOLLOW THESE INSTRUCTIONS TO AVOID PERSONAL INJURY OR DEATH: When working on or around a vehicle, the following guidelines should be observed AT ALL TIMES: Park the vehicle on a level surface, apply the parking brakes and always block the wheels.